Application Schedule

                               ACCELE-GROW-M™ FERTILIZER SUPPLEMENT APPLICATION RATES

 

                                           

______________________________________________________________________________________

                                                                 USER SAFETY RECOMMENDATIONS

 

                     Users should:

  • Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet.
  • Remove clothing immediately if fertilizer gets inside. Then wash thoroughly and put on clean clothing.
  • Remove PPE immediately after handling this product. Wash the outside of the gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.

 

                                                               STORAGE AND DISPOSAL

Do not contaminate water, food, or feed by storage or disposal.

 

FERTILIZER STORAGE: Protect from freezing and store out of direct sunlight.

FERTILIZER DISPOSAL: Wastes resulting from the use of this product may be disposed on site or at an approved waste disposal facility.

CONTAINER DISPOSAL: Triple rinse (or equivalent). Then offer for recycling or reconditioning or puncture and dispose of in a sanitary landfill, or by incineration, or if allowed by State and local authorities, by burning. If burned, stay out of smoke.

 

            ACCELE-GROW™ may be applied by ground or air. If applied by air, use 3 to 5 gallons of water per acre. If applied by ground use 5 to 25 gallons of water per acre.

For turf grass: ACCELE-GROW™ may be applied by ground using 0.2 to 0.5 gallons of water per 1,000 square feet.

 

   Test results have shown that this product can stimulate higher yields through a larger root system, earlier fruiting, increased fruit retention and improved resistance to Environmental stress. ACCELE-GROW™ is a means to increase plant efficiency.

 

 

      ACCELEGROW TECHNOLOGIES RECOMMENDS SEED TREATMENT FOR ALL DIRECT SEEDED CROPS

 

                                                           SPECIAL NOTE FOR ALL DIRECT SEEDED CROPS

 

Acting through its special combination of plant growth activators and enhancers, ACCELE-GROW is a ready to use seed dressing that aids in enhanced germination and early season root and top growth.

 

Use ACCELE-GRO as an in furrow spray at the rate of 2 ounces per acre.

 

Use ACCELE-GROW at the rate of 2 to 4 ounces per 100 lbs of seed. Use of the higher rate is recommended when conditions favor poor germination such as cool soil and low germination seed is used. Sufficient water needs to be added to insure proper coverage. Improper coverage will minimize product performance.

 

            SEED TYPE

              Alfalfa                   Corn                 Melons                 Peppers               Squash

              Barley                   Cotton               Oats                      Rice                    Sugarbeets

              Cabbage                Cucumber         Okra                     Rye                     Sunflowers

              Carrots                  Dry Beans         Onions                  Sorghum            Tomatoes

              Cauliflower           Eggplant            Peanuts                Soybeans            Wheat

              Celery                   Lettuce               Peas                      Spinach

 

RED or WHITE POTATOES:

    Dip potato seed pieces in a solution 1 part ACCELE-GRO to 350 parts water (0.40 fluid ounces per gallon) for 1 minute or spray the seed pieces until thoroughly covered and wetted. ACCELE-GROW can be used with a fungicide program.

 

SWEET POTATOES and YAMS:

     Dip potato slips in a solution of 1 part ACCELE-GROW to350 parts water (0.40 fluid ounces per gallon of water) for 60 seconds. ACCELE-GROW can be used with a fungicide program.

 

 

                                                   MECHANICAL SEED TREATERS

 

Apply the appropriate amount of ACCELE-GROW to a pre-measured amount of seed and mix thoroughly until all seeds are uniformly coated. Seed may be treated in this manner and stored until used for planting. Do not use treated seed for food, feed or oil purposes. An approved dye must be added to distinguish ACCELE-GROW treated seed and prevent inadvertent use for food, feed or oil purposes. Seed treated with this product must be labeled according to all applicable requirements of the Federal and State seed laws. DO NOT USE TREATED SEED FOR FOOD, FEED OR OIL PURPOSES.

 

 

                                                  BROADCAST SEED APPLICATION

 

Partially fill broadcast spreader with a pre-measured amount of seed. Apply the appropriate amount of ACCELE-GROW diluted with water on the surface of the seed. Mix with a stick or paddle until all the seeds are coated. Repeat procedure until broadcast spreader is full. DO NOT USE SEED FOR FOOD, FEED OR OIL PURPOSES. Treat only the amount of seed needed for immediate use and planting. Do not store seed beyond planting season.

 

                                      SPECIAL NOTE FOR ALL TRANSPLANTED CROPS

 

Two programs are recommended for this program.

  • Dip or spray roots in a solution of 1 ounce ACCELE-GRO per gallon of water prior to transplanting.
  • Bedding seedlings may be sprayed or drenched in flats 12 to 24 hours before transplanting to reduce shock with a solution of 1 ounce ACCELE-GROW per gallon of water.

 

The foliar program should begin two weeks after transplanting. A combination of the transplant and foliar spray program is most effective.

 

                                       FOLIAR SPRAY PROGRAM FOR VEGETABLE CROPS

 

 

BEANS AND PEAS:

              1st Application – apply 4 ounces per acre when first tri-foliate is un-folded.

             2nd Application – apply 4 ounces per acre two weeks after first application.

   3rd.Application – apply 4 ounces per acre at first bloom.

 

ASPARAGUS, BROCCOLI, CABBAGE, CONOLA, CELERY, LETTUCE, MINT, AND SPINACH:

     1st Application – apply 4 ounces per acre when the fifth leaf begins to unfold.

     2nd. Application – apply 4 ounces per acre two weeks after the first application.

     3rd Application – apply 4 ounces per acre two weeks after the second application.

                     

 

CANTALOPE, CUCUMBER, MUSKMELON, WATERMELON, HONEWDEW, OKRA, AND SQUASH:

     1st Application –apply 4 ounces per acre when the third leaf begins to unfold.

     2nd Application – apply 4 ounces per acre two weeks after the first application.

     3rd Application – apply 4 ounces per acre two weeks after the second application.

EGGPLANT, PEPPERS, AND TOMATOES:

               1st Application – apply 4 ounces per acre when plants have 3 true leaves.

               2nd Application – apply 4 ounces per acre at pre-bloom stage.

               3rd Application – apply 4 ounces per acre at fruit set.

 

SWEET CORN AND POP CORN:

               1st Application – apply 4 ounces per acre when plants are at the 4-6 leaf stage

               2nd Application – apply 4 ounces per acre at 8-10 leaf stage

               3rd Application – apply 4 ounces per acre just prior to tasseling. (optional)

 

RED OR WHITE POTATOES:

               Apply according to one of the following schedules:

 

               To increase tuber size number and promote better rooting:

               1st Application – apply 4 ounces per acre at tuber initiation.

               2nd Application – apply 4 ounces per acre 3 weeks after first application.

 

               To enhance tuber size and uniformity:

               1st Application – apply 4 ounces per acre at tuber initiation.

               2nd Application – apply 4 ounces per acre at onset of tuber bulking.

 

CARROTS, PARSLEY, RADISHES, AND TURNIPS:

               1st Application – apply 4 ounces per acre when the plants have 3 true leaves.

               2nd Application – apply 4 ounces per acre 2 weeks after first application.

               3rd Application – apply 4 ounces per acre 2 weeks after the second application.

              

 

SWEET POTATOES AND YAMS:

               1st Application – apply 0.20 to0.40 ounces per acre on a band just wide enough to          

                                           cover all the plants seven to fourteen days after transplanting.

               2nd Application – apply 0.50 ounces per acre in a band as above at 28 days after

                                            transplanting.

               3rd Application – apply 0.10 ounces per acre per week along with a foliar fertilizer such

                                           15-5-5 at the rate of 32 fluid ounces per acre. Continue this program     

                                           On a weekly basis until potatoes have desirable harvest size.

              

 

 

                                             FOLIAR SPRAY FOR FRUIT CROPS

 

 

 

CITRUS (GRAPEFRUIT, LEMON, LIME, AND ORANGE):

               1st Application – apply 3 to 6 ounces per acre at first bloom.

               2nd Application – apply 3 to 6 ounces per acre 2 to 3 weeks later.

               Additional applications at 3 to 6 ounces per acre may be applied if there is an

               Extended bloom period.

 

POME (APPLE, MAYHAW):

               1st Application – apply 3 to 6 ounces per acre shortly prior to or at first bloom.

               2nd Application – apply 3 to 6 ounces per acre two to three weeks after first application.

 

STONE (PEACH):

               1st Application – apply 3 to 6 ounces per acre prior to or at first bloom.

               2nd Application – apply 3 to 6 ounces per acre two to three weeks after first application.

 

STRAWBERRIES AND GRAPES:

               1st Application – apply 4 ounces per acre shortly prior to or at first bloom.

               2nd Application – apply 4 ounces per acre two to three weeks after first application.

 

BANANAS:

               1st Application – apply 3 to 6 ounces per acre prior to or at first bloom.

               2nd Application – apply 3 to 6 ounces per acre two to three weeks after first application.

 

GUAVA AND PAPAYA:

               1st Application – apply 4 ounces per acre prior to or at first bloom.

               2nd Application – apply 3 to 6 ounces per acre two to three weeks after first application.

 

 

                            FOLIAR SPRAY PROGRAM FOR FIELD CROPS

COTTON – Non- Transgenic Varieties: Apply according to one of the following schedules:

               Schedule A:

               1st Application – apply 3 fluid ounces of ACCELE-GROW per 50 lbs. of seed in the

                                           hopper box.

                                                                               OR

                                          Apply 2 fluid ounces of ACCELE-GROW per acre in the seed furrow at        

                                          planting.

               2nd Application – apply 4 fluid ounces per acre at the pinhead square stage. This can be   

                                           applied in a tank mix that contains 4 ounces per acre of mepiquate

                                chloride.

               3rd Application – apply 4 ounces per acre at early bloom.

 

  Schedule B:

               1st Application – apply 2 fluid ounces per acre on a band at the 3 to 7 leaf stage.

               2nd Application – apply 4 fluid ounces at the pinhead square stage. This can be applied

                                 In a tank mix that has 4 ounces per acre of mepiquat chloride.

     3rd Application – apply 4 ounces per acre at early bloom.

 

COTTON – Transgenic Varieties:

(cotton varieties that have been genetically manipulated to have insect-resistance and/or herbicide              

resistance built in)

               1st Application – Use according to one of the following methods.

                                           apply 3 fluid ounces of ACCELE-GROW per 50 lbs. of seed in the

                                 hopper box.

                                                                    OR

                                 Apply 2 fluid ounces per acre in the seed furrow at planting.

    2nd Application – apply 4 ounces per acre at pinhead square. This can be applied in a     

                                 tank mix that has 4 ounces per acre of mepiquat chloride.

    3rd Application – Repeat the above application at first bloom. If needed for vegetative

                                 growth control, repeat the above application at mid bloom.

 

Higher rates and/or late season applications may be warranted under high stress conditions where square and/or boll retention is needed. During the bloom and post bloom period, additional applications or higher rates of ACCELE-GROW may be applied but do not exceed a total of 24 fluid ounces per acre per season.

 

FIELD CORN:

ACCELE-GROW works best on varieties that have a tendency for multiple earring.

               1st Application – apply 4 ounces per acre at the 3-4 leaf stage.

               2nd Application – apply 4 ounces per acre at the 8-11 leaf stage

 

GRAIN SORGHUM:

               1st application – apply 4 ounces per acre at the 3-5 leaf stage.

               2nd Application – apply 4 ounces per acre after the 8th but before the 12th  leaf stage.

 

PEANUTS:

               1st Application – apply 4 ounces per acre at the 3-5 leaf stage.

               2nd Application – apply 4 ounces per acre at early flowering.

             

               3rd Application – apply 4 ounces per acre at initial pegging.

              

 

SOYBEANS: Apply to foliage according to one of the following recommended schedules.

               Schedule A:

               1st Application – apply 4 ounces per acre at the 3-5 trifoliate leaf stage.

               2nd Application – apply 4 ounces per acre prior to bloom.

                                                                               OR

               Schedule B:

               If the first application is missed apply 8 fluid ounces per acre prior to bloom.

 

SUGARBEETS:

               1st Application – apply 4 ounces per acre after thinning.

               2nd Application – apply 4 ounces per acre two to three weeks after first application.

 

SUGARCANE:

               1st Application – use one of the following methods.

                                           Apply 2 fluid ounces per acre in the furrow at planting.

                                                         OR

                                           Apply 4 fluid ounces per acre at 2-3 leaf stage.

               2nd Application – apply 4 ounces per acre one month after first application

 

ALFALFA, BARLEY, OATS, RYE, AND WHEAT: Apply according to one of the following

               schedules.

               Schedule A:

               1st Application – apply 4 ounces per acre prior to jointing.

               2nd Application – apply an additional 4 ounces per acre at the flag leaf stage.

                                                OR

     Schedule B:

     If the first application is missed in schedule A, apply 8 ounces per acre at the flag leaf stage.

 

 

FLAX: apply according to one of the following schedules:

               Schedule A:

               1st Application – apply 4 ounces per acre when plant is 2-4 inches tall.

               2nd Application – apply 4 ounces per acre two to three weeks later.

 

SUNFLOWERS:

               1st Application – apply 4 ounces per acre at 4 true leaves.

               2nd Application – apply 4 ounces per acre two to three weeks later.

 

 

                                                   FOLIAR SPRAY PROGRAM FOR RICE

ACCELE-GROW should be applied at 4 ounces per acre as a foliar spray to the plant during either one of the following stages of development.

 

PRIMARY RECOMENDATIONS – 3 to 7 LEAF STAGE: This application must be made after the rice seedling has 3 fully emerged leaves and the forth leaf is beginning to emerge but before the seedling has completed development of 7 leaves or 3 tillers. This period for application generally begins 3 to 6 weeks after seeding and ends 5 to 9 weeks after seeding. The duration of this period depends on the variety and the growing conditions. This application may be made in conjunction with corresponding herbicide application.

 

ALTERNATE RECOMMENDATION – TWO MILLIMETER (mm) PANICLE GROWTH STAGE: If the primary application is missed, ACCELE-GRO can be applied to stimulate cell differentiation in the developing panicle. This application must be made when no more than 10% of the main culms are at the 2mm panicle growth stage. The 2mm panicle growth stage occurs immediately after internode elongation or joint movement has begun. ACCELE-GROW must applied as soon as internode elongation is detected so the 2mm panicle growth stage is not missed. It is better to apply slightly early than to apply late. IMPORTANT: timing of the application at 2mm growth stage is critical. Check the entire field for stage of plant development.

Large fields may require split applications on upper and lower ends of the field to ensure proper timing throughout the field.

 

                                                              HAY and PASTURE

 

HAY: Apply 8 ounces per acre at first greening in the spring. Apply 8 ounces per acre after each cutting after new growth starts greening.

 

PASTURE: apply 4 ounces per acre every 90 days. Allow 2 weeks of new growth before resuming livestock grazing

 

                                                               TURFGRASS

 

On all turfgrass regardless of type, use no more than 6 fluid ounces per 1000 square feet per month should be used.

 

WARM SEASON TURF:   (Bermuda, Bermuda hybrids, Zoysia, Centipede, St. Augustine, etc.)

For lower traffic areas and where ACCELE-GRO is used as a maintenance program, begin applications early in the growing season. Apply at the rate of 1 to 2 fluid ounces per 1000 square feet. Maintenance application should be made on a two to three week schedule throughout the growing season. Application may be made with foliarly-applied urea for added benefits.

 

COOL SEASON TURF: (Tall Fescue, Rye, Bentgrass, Bluegrass, etc.). Apply 1.5 to 2 ounces per 1000 square feet in fall, or when stand is established. Repeat application in late winter when grasses begin to grow actively.

 

APPLICATION WITH FOLIARLY-APPLIED UREA:  Maximum benefit and color can be achieved when ACCELE-GROW applications are made with foliarly-applied urea solutions. To prepare urea solution, dissolve 46% urea into spray solution at the rate of 1.0 lb. per 5000 square feet to be sprayed and apply with recommended rate of ACCELE-GROW.

 

 

                                                SPECIFIC RATES OF APPLICATION

 

 

TEES AND GREENS: Apply 1 to 2 ounces per 1000 square feet on a 2 week schedule throughout the growing season. Begin in early spring after grasses have begun to grow.

 Sunbelt and transition zones should continue spray program throughout playing season. Courses north of the transition zone should continue applications thru September.

 

FAIRWAYS: Begin applications in early spring as soon as grasses have began to actively grow. Apply 1 ounce per 1000 square feet and repeat on a monthly schedule as long as grass is growing.

 

 

PRE TOURNAMENT QUICK GREEN UP: Apply at the rate of 1 to 2 ounces per 1000 square feet in conjunction with urea solution 4 to 5 days before tournament. Make application with a minimum spray volume of 0.50 gallon of water per 1000 square feet.

 

 

The SPRING DORMANCY BREAK: Apply 1 fluid ounce per 1000 square feet in spring as soon as new growth (opening) is visible. Raking of thatch prior to making this application is most desirable. Application at this time generates rapid growth and often can reduce incidence of “spring die back” on certain species of grass.

 

 

FALL APPLICATION FOR WINTER HARDINESS: Make 2 applications 7-10 days apart in late summer or early fall just prior to cessation of normal active growth. Apply 1 to 2 ounces per1000 square feet. Make application with a spray volume of 0.50 gallon of water per 1000 square feet. Applications at this time will greatly increase root mass and depth of roots. Winter kill problems are often greatly reduced.

 

 

COMMERCIAL TURF, CEMETERIES, ATHLETIC FIELDS, GOLF COURSES, and OTHER FINE TURF: Applications of 1 to 2 ounces per 1000 square feet made at any point during the growing season will produce desirable results. Make applications during the very early growth stages and continue on a monthly schedule throughout the growing season. Healthier and more beautiful turf can be realized in high traffic areas such as greens and tees by making regular applications every two weeks.

 

 

  SOD FARMS: Apply 4 to 8 fluid ounces per acre on a monthly basis during growing season. Two weeks prior to cutting sod apply 4 to 8 ounces per acre.

 

SPECIFIC RATES OF APPLICATION: After sod is cut, a re-establishment program is necessary. This program should start as soon as there is any greening over 30% of the area.

Spray with 4 to 8 ounces per acre of ACCELE-GROW. Repeat in two weeks, and thereafter, once per month throughout the growing season. Make a final application of 4 to 8 ounces per acre two weeks before dormancy.

 

Start the program again as soon as some green-up has started in the spring.

 

When species started from seed have reached 1 inch of height, the monthly treatment may be started and followed in the same way as non-seeded varieties.

 

                                  SPECIAL NOTE FOR ALL DIRECT SEEDED GRASSES

Acting through its special combination of plant growth enhancers, ACCELE-GROW is a ready to use seed dressing that aids in enhancing germination and early season root and top growth.

 

ACCELE-GROW can be used at the rate of 4 fluid ounces per 100 lbs. of seed. Sufficient amounts of water should be added to insure proper coverage. Improper coverage will minimize product performance.

 

ACCELE-GROW IS A FERTILIZER SUPPLEMENT. ALWAYS USE WITH A GOOD FERTILIZER PROGRAM.

 

            ACCELEGROW™ and ACCELE-GROW-M™ and Design are Trademarks of Accelegrow Technologies, Inc.

 

                                                             CONDITIONS OF SALE AND WARRANTY

 

All statements concerning the use of this product apply only when used as directed. The directions for use of this product reflect the opinions based on field use and test and should be followed carefully. However, it is impossible to eliminate all risks associated with use of this product. Crop injury, ineffectiveness, or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or the manner of use or application all of which are beyond the control of  Accelegrow  Technologies, Inc. or the Seller. All such risk shall be assumed by the Buyer.

 

 

Accelegrow Technologies, Inc. warrants that this product conforms to the chemical description on the label and is reasonably fit for the purpose referred to in the Directions for Use subject to the inherent risks referred to.  Neither Accelegrow Technologies Inc., The Seller nor their Respective affiliates  makes any warranty express or implied, including, but not limited to Warranties of Fitness or Merchantability other than as stated in the preceding sentence.

 

In no case shall Accelegrow Technologies, Inc., The Seller or their Respective Affiliates, be liable for consequential, special, or indirect damages resulting from the use or handling of this product. The exclusive remedy of the user or buyer of this product, and the limit of liability of Accelegrow Technologies, Inc., The Seller or their respective Affiliates, for any loss, damages, or injuries resulting from the use or handling of this product shall be the replacement of any nonconforming product or the refund of its purchase price as determined by Accelegrow Technologies, Inc. in its sole discretion.

 

Accelegrow Technologies, Inc. and the Seller offer this product and the Buyer and user accept it, subject to the foregoing Conditions of Sale and Warranty, which may be varied only by agreement in writing signed by a duly authorized representative of Accelegrow Technologies, Inc.